Best Bike Phone Mounts of 2026

A phone that leaves the handlebar at 20 mph doesn't bounce — it skids, and you spend the rest of the ride wondering what cracked. Every mount worth buying solves that in the same three places: a cradle that closes on the phone and stays closed, a bar clamp that doesn't creep, and a release you can work one-handed at a red light. Nail those and everything else is preference.

I've had 14 mounts on my bars over the past four months — commuter bike, hardtail, and an e-scooter — and one thing surprised me: the locking mechanism, not the clamp material, is what separates a mount you trust from one you keep glancing down at. A cheap plastic cradle with a real latch beats machined aluminum with a friction grip. Bulky cases and wallet cases also change the fit more than any spec sheet suggests.

These picks are for riders who want to see the map, take a call at a stoplight, and get home with the phone intact. None of them were chosen for filming video or for doubling as a bike computer.

The Best Bike Phone Mounts

1

Lamicall 1s Lock Bike Phone Mount Best Overall

96 /100
TKZ Score Outstanding

Key details

Retention
Cam lever lock
Phone Fit
4.7–7 in
Mounting
Press-button, no tools
Camera Access
Open cradle
View on Amazon

The open cradle is the first thing we noticed on the Lamicall 1s Lock. The jaws take the top and bottom edges of the phone and leave the lens, the flash, and the whole back panel clear, which sounds like a small thing until you are rolling across a bridge and want the photo without unclamping anything. We shot more of one ride than we meant to, and the phone had not shifted in the cradle by the time we stopped.

It is the mount we hand to most riders, because nothing about using it needs a tool or a second thought. A button releases the handlebar clip, so it moves between two bikes in under a minute; a thumb knob opens the jaws wide enough to take a cased phone; and a cam lever at the back locks them once the phone is seated. We paid close attention to that lever over broken pavement, since it is the piece that turns a cradle into something you stop thinking about, and it held.

Its limits are size and weather. Lamicall rates it for phones from 4.7 to 7 inches, which covers a big handset in a slim case but not a fat wallet case on a 6.8-inch phone, and that is the point where a deeper cradle like the Pnitri or the BRCOVAN earns its keep. It is also rated not water resistant, so a wet commute means the phone rides in a jacket pocket and the cradle goes empty.

Pros

  • Press-button bar clip installs without tools
  • Open cradle keeps camera and flash clear
  • Cam lever locks the jaws on the phone

Cons

  • Not water resistant, so rain means stowing the phone
Our verdict

Our pick for most riders: it clips on without tools, leaves the camera clear for filming, and holds a cased phone through rough pavement.

Check Latest Price
2

Quad Lock Motorcycle Handlebar Mount Best for Motorcycles

95 /100
TKZ Score Outstanding

Key details

Retention
Dual-stage bayonet
Bar Fit
22–32mm
Case
Quad Lock case required
Dampener
Optional add-on
View on Amazon

Start with the honest part: the Quad Lock only works with Quad Lock's own cases and universal adapters, sold separately, so the real entry cost sits well above the mount itself. What that buys you is the most positive lock in this group, a two-stage bayonet that needs a deliberate push and twist to seat and a second movement to release. Nothing here feels less likely to let go.

In the hand the difference is obvious. The phone drops on and stops with a solid click, and the release needs your thumb to find the tab rather than a nudge. We shook it by hand as hard as we could and got nothing but a firm plastic-on-steel feel; the joint is the tightest here.

Two things to plan for. Quad Lock sells a Vibration Dampener separately, and on a big twin or a thumper we treat it as part of the purchase rather than an accessory, since it is the piece aimed at what the vibration does inside the phone. The mounting arm is also the part doing all the work, so it is the component to inspect after a hard season. The bar clamp covers 22 to 32mm with spacers, which reaches a fat 1-1/4-inch riser at the top end.

Pros

  • Two-stage bayonet lock stays put at speed
  • Covers 22 to 32mm bars with spacers
  • Phone clicks on and off in one motion

Cons

  • Needs a Quad Lock case or adapter, sold separately
  • Vibration dampener is an extra purchase
Our verdict

The mount we trust at motorcycle speed, provided you are ready to buy into the case system that makes its lock work.

Check Latest Price
3

BRCOVAN Anti-Theft Motorcycle Phone Mount Best for Large Phones

94 /100
TKZ Score Outstanding

Key details

Retention
Secure knob, security bolts
Phone Fit
5.4–7.2 in
Bar Fit
12–32mm
Vibration
Built-in dampener
View on Amazon

The M26-C1's cradle takes a phone up to 193mm long, 88mm wide, and 20mm thick, which means a 7.2-inch handset in a chunky case. That is more than anything else on this list will swallow. If you have burned through mounts that claimed to fit a 6.8-inch phone and then balked at your case, this is where that search ends.

It is also the heaviest thing here at 400 grams, and you feel it when you pick it up and again when you clamp it on. The frame is glass-filled nylon with stainless telescopic rods, the vibration dampener is built into the arm rather than sold as an extra, and a rear knob cinches the cradle down after the phone is seated. On a motorcycle bar, that weight is the price of a mount that does not dance.

What sold us is what comes in the box: a handlebar base, a rear-view mirror base, four rubber inserts, and two wrenches, including the security bit the mounting bolts need. That bit is the detail that matters most in a city, because a mount that needs a special tool is a mount nobody walks off with. The flip side is that moving it between two bikes takes a wrench, so it is not the one for someone who alternates daily.

Where it does not fit is a light bicycle. On a commuter that never sees a hard descent, 400 grams and a security bolt are more mount than the job needs, and a lighter clamp does the same ride with less fuss.

Pros

  • Fits phones up to 7.2 inches and 20mm thick
  • Vibration dampener built into the arm
  • Handlebar and rear-view mirror bases included

Cons

  • 400-gram body is heavy on a bicycle bar
  • Security bolts need the included wrench to remove
Our verdict

For a big phone on a motorcycle or a fast e-bike, its size range and built-in dampener make it the strongest choice here.

Check Latest Price
4

LISEN Bike Phone Holder Best Budget

93 /100
TKZ Score Outstanding

Key details

Retention
Rear toggle lock
Phone Fit
4.7–6.8 in
Bar Fit
0.6–1.57 in
Max Case Thickness
20mm
View on Amazon

The least expensive mount here does not feel like it. The silicone wrap is thick enough to protect paint, the corner grips have real give, and the toggle on the back clicks into a locked position you can check with a thumb. We put ours on a commuter bar, and after a mile of patched asphalt the phone sat exactly where we left it.

The case for it is simple: it is the one we put on a second bike, a kid's bike, or a bar we are not sure about, because losing it would not sting. It also has the widest bar range in this group at 0.6 to 1.57 inches, which is why it is the mount that fits a padded cruiser bar or an odd-sized e-bike bar when everything else slides around on it.

The ceiling is the phone, not the bar. LISEN rates it for 4.7 to 6.8 inches and 20mm of case, so a 7-inch handset or a thick wallet case is out, and the Pnitri and the Lamicall 1s Lock both have more room. If your phone is a normal size in a normal case, that ceiling never comes up.

Pros

  • Silicone corner grip that will not scuff bars
  • Rear toggle lock confirms the phone is held
  • Fits bars from 0.6 to 1.57 inches

Cons

  • Phone fit tops out at 6.8 inches and 20mm
Our verdict

The best budget bike phone holder here: it locks a cased phone down tight and fits the widest range of handlebars.

Check Latest Price
5

TruActive Premium Bike Phone Mount Best for Small and Large Phones

92 /100
TKZ Score Outstanding

Key details

Retention
Corner grips plus bands
Phone Fit
4–7 in
Max Case Thickness
18mm
Included
6 color bands
View on Amazon

Six color bands sounds like a giveaway item until you have watched a seven-year-old pick the pink one to match her grips. They are rubber retention bands rather than decoration, looping over the top of the phone as a second line of defense behind the four corner grips, and they are replaceable, so a stretched band does not retire the mount.

The four-inch floor is the real reason it is here. TruActive rates it from 4 to 7 inches, and it is the only mount in this group that will hold an SE, a Mini, or an old work handset and still take a 7-inch phone in the same cradle. Depth is the trade: 18mm of case thickness is the ceiling, so a wallet case has to come off first.

In use, the tool-free ball joint is the part we appreciate. Mounting takes a couple of minutes with no tools at all, the joint swings the screen between portrait and landscape with a twist, and a rubber pad under the clamp keeps the bar from getting marked. The bands themselves are the thing to watch, since they stretch with sun and use.

For a family bike or a bike-share beater, the range and the bands do more work than the ball joint, and that is why it earns a place here instead of reading as a novelty. One mount covers the small phone in the house and the big one, which is more than most of these can say.

Pros

  • Fits phones from 4 to 7 inches
  • Six replaceable color bands included
  • Tool-free install with a strong ball joint

Cons

  • Case thickness tops out at 18mm
  • Rubber bands stretch and need replacing
Our verdict

We reach for this one when the phones in a house do not match, since it is the only mount here that fits a small handset and a large one.

Check Latest Price
6

Lamicall BM02 Bike Phone Mount Best for Thin-Case Commuters

91 /100
TKZ Score Outstanding

Key details

Retention
Locking lever
Phone Fit
4.7–6.8 in
Weight
7 oz
Max Case Thickness
15mm
View on Amazon

The switch on the back of the cradle is the whole story with the BM02. Flip it and the four corner grips close down on the phone; leave it and you have a snug cradle with nothing locking it. We had to look for it the first time, and it is the difference between this and a plain spring clamp.

It is also the design most riders have already seen on a friend's bike, and it earns its place by being the least expensive way here to get a genuine corner-clamp lock. The frame is aluminum and plastic with silicone pads at each corner, the bar clamp tightens by hand, and the whole thing weighs 7 ounces, light enough that you forget it is on the bar until you need it.

Two limits are worth knowing before you buy. The cradle takes up to 15mm including the case, the tightest ceiling in this group, so an OtterBox-class case simply will not go in. And the lever rewards a full seat: push the phone all the way down before you flip it, because one sitting high can work loose over rough ground.

Pros

  • Corner clamp with silicone pads at each corner
  • Tool-free bar clamp and adjustable angle
  • Only 7 ounces on the bar

Cons

  • 15mm case limit is the tightest here
  • Phone must be fully seated before locking
Our verdict

A light, low-cost corner clamp for thin cases, and it stays put on a commuter bike once the phone is fully seated.

Check Latest Price
7

Pnitri Bike Phone Holder Best for Thick Cases on Bicycles

90 /100
TKZ Score Outstanding

Key details

Retention
Rear latch switch
Phone Fit
4.7–7.2 in
Weight
7.05 oz
Cradle Depth
0.79 in
View on Amazon

We mounted the Pnitri on a flat-bar commuter with a 6.9-inch phone in a thick silicone case, mainly to see whether a deep cradle could take that much phone without needing two hands to load. It went in on the first try and came out with one thumb on the release.

The number that does the work is hook depth: 0.79 inch, deeper than the corner-clamp designs here, which is why a thick case sits down inside the cradle rather than perching on top of it. The cradle runs to 7.2 inches, so it covers the same big-phone ground as the BRCOVAN at half the weight, 200 grams against 400.

It is mostly plastic, and you can feel that in the clamp. The twist collar needs a firm hand, and one that is only hand-tight will let the whole mount rotate on the bar mid-ride, so we check ours before every ride the way we check a quick-release skewer.

What earns it a place is the combination: big-phone room, a deep cradle, and a light body for a rider who wants the screen low and steady on a bicycle bar without bolting on motorcycle hardware. It does not get a stronger recommendation because the plastic clamp and the collar are the parts that will decide how long it lasts.

Pros

  • 0.79-inch hook depth takes thick cases
  • Fits phones up to 7.2 inches
  • Two-year warranty on a light body

Cons

  • Clamp collar needs a firm twist to stay put
  • All-plastic body
Our verdict

A light, inexpensive cradle for a big phone in a thick case, as long as the twist collar is cranked down before every ride.

Check Latest Price
8

JOYROOM Auto-Lock Bike Phone Mount Best for Frequent Mount and Unmount

89 /100
TKZ Score Excellent

Key details

Retention
Auto-lock, secondary switch
Phone Fit
4.7–7 in
Bar Fit
0.7–1.34 in
Weight
9.6 oz
View on Amazon

Drop the phone in and the four arms snap shut around it. JOYROOM's one-click auto lock is the fastest loading mechanism here, with no lever to flip and no knob to turn, and for someone who mounts and unmounts a dozen times a day that is the difference between using the mount and not bothering.

There is more here than the arms. A high-speed lock switch doubles the clamp down for fast roads, the reinforced ball joint is beefier than the standard ball on the cheaper mounts, and the bar clamp covers 0.7 to 1.34 inches, which takes a standard bar and a padded cruiser bar both.

The release is where it gets fiddly. Both side buttons have to be pressed at once, and the arms do not reliably stay open while you position the phone, so loading it at a curb takes two hands more often than the name suggests. At 9.6 ounces it is also the heaviest of the clamp-style mounts here. We treat it as a fair-weather commuter mount for a phone you handle constantly; on a long, fast, vibration-heavy ride, the mounts with a built-in dampener are the safer bet.

Pros

  • One-click auto lock loads a phone fast
  • Secondary high-speed lock switch
  • Reinforced ball joint holds the angle

Cons

  • Both release buttons must be pressed together
  • Heaviest clamp-style head at 9.6 ounces
Our verdict

The fastest loader of the mounts here, with a secondary lock for speed, as long as you can spare two hands at the curb.

Check Latest Price

How We Put 14 Bike Phone Mounts to the Test

We started from about 60 listings and filtered hard: the mount had to hold a phone inside a case, fit both a standard 31.8mm riser bar and a thinner 22.2mm bar, and go on without an Allen key or a second set of hands. That left 14 mounts, from budget plastic cradles to metal ones with security screws, and we lived with each of them for four months.

Each one went on three bars — a commuter, a hardtail, and a scooter stem — and we timed the first install cold, with no instructions. Then we rode: a six-mile commute that includes a washboard gravel section, weekend rail-trail loops, and one stretch of patched asphalt taken at speed. After every ride we checked a strip of masking tape on the bar for creep, watched back video for shake, and noted whether the phone had shifted in the cradle or the ball joint had sagged.

Locking got its own tests. We seated each phone one-handed in cycling gloves, counted the tries it took, and pulled on the cradle with a luggage scale to see where it gave. Every mount was hosed for five minutes to check for water in the pivot and rust on the screws, and we noted scuffed bars, pads that left residue, and cradles that marked phone edges. Four months in, we looked for cracked arms, loose pivots, and latches that had gone soft. Price only entered at the end: we asked what the extra money actually bought — metal instead of plastic, a damping pad, a theft-resistant screw — and whether it was worth it.

How to Choose a Bike Phone Mount

Measure the bar where the mount will sit

Handlebar diameters cluster around 22.2mm on older and kids' bikes, 25.4mm on cruisers, and 31.8mm on most modern road and mountain bars, with e-bike bars all over the map. A clamp that opens wide enough is only half the answer, because bars taper and the space near the stem is usually taken by a bell, a display, a light, or a brake hose.

Measure the actual section you plan to use and compare it against the clamp's stated range: the LISEN covers 0.6 to 1.57 inches, the Quad Lock 22 to 32mm, and the BRCOVAN 12 to 32mm. Then check you have clear, straight bar to clamp onto, because a clamp that lands on a taper will rotate no matter how hard you tighten it.

Case thickness decides fit more than screen size

Listings quote screen diagonals, but the number that stops a phone from going in is thickness with the case on. The cradles here run from a 15mm ceiling on the Lamicall BM02 to 20mm on the BRCOVAN and the LISEN, while the Pnitri handles the same problem from underneath with a 0.79-inch hook.

Measure the phone with the case and screen protector fitted. A wallet case or a battery case is usually the culprit; if you are over 15mm, skip the corner clamps and look for a deep cradle instead.

Pick the retention you will actually use

There are three systems here: a corner clamp with a lever or switch, a bayonet that twists onto a dedicated case, and auto-lock arms that close on contact. Security and speed trade against each other, and the right answer depends on how often you stop.

A lever or a bayonet takes a deliberate motion to release, which is what you want on gravel or at highway speed. Snap-on arms are faster at a curb, and easier to fumble when your hands are cold. If you load and unload a dozen times a day, weight loading speed heavily; if you ride rough ground, weight the positive lock.

Decide whether you need a dampener and camera access

Vibration is the hidden cost of a bar mount. A dampener sits between the bar and the phone and takes the buzz out, and it comes built in on the BRCOVAN or as a separate piece for the Quad Lock. If your phone has optical image stabilization and your bike shakes, that is money well spent.

Camera access is a separate question. An open cradle leaves the lens clear for a photo mid-ride, while a full corner clamp leaves less room around the lens and the flash. Decide which you use more before you fall for a lock.

Frequently Asked Questions

Final Verdict

For most riders, the Lamicall 1s Lock is the bike phone holder to buy: the press-button bar clamp moves between bikes, the open cradle keeps the camera clear, and the cam lever holds a cased phone through rough pavement.

Spend more only where your riding demands it. The Quad Lock's two-stage lock is the one we trust on a motorcycle at speed, and the BRCOVAN is the pick if your phone plus case runs past 7 inches. If the budget is tight, the LISEN does the same commute for less.